Struggling with your Husqvarna 350 chainsaw? Don’t worry, you’re not alone!
From starting issues to chain tension problems, many users face common challenges.
In this guide, we’ll walk you through 10 common Husqvarna 350 Chainsaw Troubleshooting tips, complete with simple fixes to get your chainsaw running smoothly again.
Let’s make those tough jobs easier!
Husqvarna 350 Chainsaw Troubleshooting (Short Overview)
If your Husqvarna 350 chainsaw isn’t working properly, start by checking the basics fuel levels, spark plug, and air filter.
Clean or replace these parts as needed. For starting issues, ensure the carburetor is adjusted correctly.
Regular maintenance and quick fixes can keep your chainsaw running smoothly.
Read 10 Common Troubleshooting With Fixes In Easy Ways…
1. Fuel Issues
Fuel problems are a common cause of trouble with the Husqvarna 350 chainsaw. If the engine struggles to start, stalls, or runs unevenly, the fuel system could be the culprit.
Causes
- Using stale or contaminated fuel
- Incorrect fuel-to-oil ratio
- Blocked fuel filter or fuel line
Fixes
- Drain and replace old fuel with fresh, properly mixed fuel (50:1 ratio of gas to oil).
- Clean or replace the fuel filter to ensure proper fuel flow.
- Inspect and clear any debris from the fuel line.
2. Spark Plug
The spark plug is a key part of your Husqvarna 350 chainsaw’s engine. If the chainsaw isn’t starting or running smoothly, a faulty or dirty spark plug could be the issue.
Start by inspecting the spark plug for damage, soot, or wear.
Causes:
- Worn-out or cracked spark plug.
- Excessive carbon buildup on the plug.
Fixes:
- Clean the spark plug with a wire brush to remove carbon deposits.
- Replace it with a new one if it’s damaged or excessively worn.
3. Air Filter
The air filter in your Husqvarna 350 chainsaw plays a critical role in ensuring smooth operation.
Cause
A dirty or blocked air filter can result from extended use, especially in dusty or debris-filled environments. Over time, this buildup restricts airflow, affecting engine performance.
Fix
Clean the air filter regularly using compressed air or soapy water (if it’s washable). If the filter is worn out or damaged, replace it with a new one to restore proper airflow.
Always follow the manufacturer’s guidelines for maintenance.
4. Carburetor Adjustment
If your Husqvarna 350 chainsaw is stalling, idling roughly, or struggling to start, the issue might lie in the carburetor.
The carburetor controls the mix of fuel and air, so improper settings can lead to performance problems.
Causes
- Incorrect fuel-air mixture, either too rich or too lean.
- Debris or dirt clogging the carburetor.
Fixes
- Adjust the carburetor screws (labeled L, H, and T) to fine-tune the fuel-air ratio.
- Clean the carburetor thoroughly to remove blockages.
- Test the chainsaw after adjustments to ensure smooth operation.
Read Also:
Homelite chainsaw troubleshooting
5. Chain Tension
Proper chain tension is essential for the Husqvarna 350 chainsaw to work efficiently and safely.
Causes
- Loose chain due to regular use.
- Incorrect installation of the chain.
Fixes
- Adjust the chain tension using the tensioning screw until it fits snugly against the bar but can still move freely.
- Always check the tension before use to ensure optimal performance and safety.
6. Engine Flooding
Engine flooding is a common issue with the Husqvarna 350 chainsaw, often caused by too much fuel entering the engine, making it hard to start.
Causes of Engine Flooding
- Choke left on for an extended time.
- Over-priming the engine.
- Repeated unsuccessful starting attempts.
Fixes for Engine Flooding
- Turn off the choke and let the chainsaw sit for 15-30 minutes to allow excess fuel to evaporate.
- Remove and dry the spark plug, then try starting again.
- Use the “pull-start” method with the throttle fully open to clear the chamber.
7. Starter Rope
If your Husqvarna 350 chainsaw’s starter rope isn’t working, it can stop you from starting the engine altogether.
Causes:
- The starter rope is tangled or jammed in the recoil housing.
- The rope has worn out or snapped due to regular use.
Fixes:
- Open the recoil housing and check for tangles or obstructions. Untangle the rope gently or replace it if needed.
- If the rope is damaged, replace it with a new, durable starter rope to restore smooth operation.
8. Bar Oil Flow
Proper bar oil flow is essential for the smooth operation of your Husqvarna 350 chainsaw. If the chain isn’t getting enough oil, it may overheat or wear out quickly.
Causes:
- Clogged oil lines blocking the flow.
- A malfunctioning oil pump.
- Insufficient bar oil in the reservoir.
Fixes:
- Clear out any blockages in the oil lines using compressed air or a cleaning tool.
- Inspect and replace the oil pump if it’s not functioning.
- Refill the bar oil reservoir and check for proper flow before use.
9. Ignition Coil
The ignition coil is a critical component of your Husqvarna 350 chainsaw. If the chainsaw isn’t starting or runs inconsistently, a faulty ignition coil could be the cause.
This part generates the spark needed to ignite the fuel mixture in the engine, so any issues with it can prevent the chainsaw from functioning properly.
Common Causes
- Worn-out or damaged ignition coil
- Loose or corroded wiring connections
- Internal short circuits in the coil
Fixes
- Inspect the ignition coil for visible damage or wear
- Test the coil using a multimeter to ensure proper functionality
- Replace the ignition coil if it’s defective or beyond repair
10. Overheating
Overheating is a common issue with the Husqvarna 350 chainsaw, and it can affect its performance and lifespan if not addressed.
When the chainsaw overheats, it may shut down unexpectedly or struggle to operate efficiently, which can be frustrating during use.
Identifying the root causes and applying the right fixes can help keep your chainsaw running smoothly.
Causes
- Clogged Air Filters: Restricted airflow due to dirty air filters can cause the engine to overheat.
- Dull or Improperly Adjusted Chain: A dull chain forces the engine to work harder, generating excess heat.
- Insufficient Lubrication: Lack of bar and chain oil increases friction, leading to overheating.
Fixes
- Clean or Replace Air Filters: Ensure air filters are cleaned regularly or replaced if heavily clogged.
- Sharpen or Adjust the Chain: Keep the chain sharp and properly tensioned to reduce strain on the engine.
- Check Lubrication Levels: Regularly refill bar and chain oil to maintain proper lubrication and prevent heat buildup.
FAQs
What is the price of the Husqvarna 350 chainsaw?
The price of the Husqvarna 350 chainsaw varies depending on the seller and condition but typically ranges from $200 to $400 for used models, as it is no longer in production.
Is the Husqvarna 350 chainsaw any good?
Yes, the Husqvarna 350 chainsaw is highly regarded for its reliability, power, and durability, making it a popular choice among both homeowners and professionals.
How old is a Husqvarna 350 chainsaw?
The Husqvarna 350 chainsaw was first introduced in the late 1990s and discontinued in the mid-2000s, making it over 15 years old.
How big of a bar can you put on a Husqvarna 350?
The Husqvarna 350 chainsaw can accommodate a guide bar ranging from 13 to 20 inches in length.
[…] 10 Common Husqvarna 350 Chainsaw Troubleshooting (With Fixes) […]